Subsonic Load Data

You can find all our subsonic loads below with all details available. You only require an access licence to unlock and view the exact powder charges. Find your relevant load data by using the filters for caliber, bullet weight, bullet diameter, and bullet manufacturer.

Compare for all suitable powders key characteristics such as powder charge, load ratio, maximum pressure, velocity and powder conversion. Also see how loads perform for different barrel length which is particularly important for regions where silencers are allowed.

Subsonic load data

Filter subsonic load data

Subsonic loads by caliber and bullet

64 combinations — page 2 of 2

Subsonic calibers with load data

Subsonic reloading: what the data means

What counts as a subsonic load

A subsonic load is one whose projectile never exceeds the local speed of sound, so it produces no ballistic crack downrange. At sea level and around 20 °C the speed of sound is roughly 1,125 fps (343 m/s); in cold, dense air it drops towards 1,050 fps (320 m/s). Because air temperature, altitude and humidity move that threshold by several dozen feet per second, a practical subsonic load is usually built with a margin: most reloaders target 1,000–1,080 fps (305–330 m/s) at the muzzle so the bullet stays clearly below the transonic region across a realistic temperature range. Loads that sit right at the sound barrier are the worst of both worlds — as the projectile decelerates through the transonic band it is buffeted by shifting shockwaves, which visibly degrades grouping at longer distances. Every combination listed here is calculated for velocities in that subsonic window, using the same inner-ballistics model as our supersonic load data, with charge weight, fill ratio, calculated peak pressure and muzzle velocity per powder.

Powder selection for reduced charges

Subsonic loads are, by definition, heavily reduced in energy, and that changes which propellants behave well. Fast-burning pistol and shotgun powders as well as dedicated reduced-load powders reach a stable pressure peak with small charges and a short pressure curve, which is why they dominate subsonic rifle recipes. Slow rifle powders designed for full-capacity magnum loads often burn incompletely at subsonic charge weights: the result is erratic velocity, heavy unburnt residue, extreme muzzle flash and, above all, poor shot-to-shot consistency. Fill ratio is the number to watch. A charge that occupies only a small fraction of the case can lie in different positions depending on how the rifle is held, which changes ignition timing and produces velocity spreads far larger than the same powder would give at full capacity. Bulky powders, powders with additives that stabilise reduced loads, or a filler-free case design that keeps load density high all reduce that effect. Our tables show the fill ratio next to each charge precisely so you can favour combinations that fill the case sensibly rather than the ones that merely hit the velocity target.

Squibs, detonation and other subsonic-specific risks

Two failure modes deserve special attention when you go below the sound barrier. The first is the squib: a charge so small or so poorly ignited that the bullet leaves the case but stops inside the barrel. The next round fired into an obstructed bore will destroy the firearm and can seriously injure the shooter. Subsonic loads sit much closer to that threshold than full-power loads, so never fire the next shot after an unusually quiet report, a weak recoil impulse or a missing impact — unload and check the bore. The second is the disputed but well-documented phenomenon of a pressure excursion with very small charges of slow powder in large cases, sometimes called secondary explosion effect or detonation. Whatever the mechanism, the practical rule is unambiguous: do not invent your own extreme reduced load with a slow rifle powder, and do not go below the minimum charge shown for a combination. Also remember that a subsonic load frequently will not cycle a semi-automatic action reliably. Short-stroking, failures to eject and out-of-battery conditions are handling risks in their own right, which is why many subsonic shooters run their rifles manually or fit an adjustable gas system.

Twist rate and stability for heavy subsonic bullets

Because energy scales with the square of velocity, subsonic shooters compensate with mass: 190–230 gr in .308", 300 gr and heavier in .338", 500 gr and up in .458". Those projectiles are long relative to their diameter, and gyroscopic stability depends on length far more than on weight. At roughly one third of normal muzzle velocity, the spin rate delivered by a given twist is also roughly one third — so a barrel that stabilises a 175 gr match bullet at 2,600 fps may not stabilise a 220 gr subsonic bullet at 1,050 fps. This is why dedicated subsonic barrels use much faster twists: 1:8" or 1:7" in .300 Blackout, 1:3" in 8.6 Blackout, and comparably fast rates in other subsonic-oriented chamberings. Check the recommended twist listed on the bullet page against your actual barrel before you invest in components, and treat keyholing on paper as the unambiguous sign that the projectile is too long for your twist. Seating depth matters too: heavy subsonic bullets are frequently seated deep, which reduces usable case capacity and shifts the whole pressure picture — the reason our data is calculated per cartridge overall length rather than assumed.

Suppressor-relevant guidance

A suppressor removes the muzzle blast; only a subsonic projectile removes the ballistic crack as well, which is why the two are almost always used together. Some practical consequences follow from that pairing. A suppressor adds volume behind the bullet and typically raises muzzle velocity slightly, so a load verified as subsonic unsuppressed can creep over the threshold once the can is fitted — verify over a chronograph in the configuration you actually shoot. Fouling increases markedly, both in the suppressor and, on gas-operated rifles, in the action, and reduced charges of poorly matched powders make it worse. First-round pop, the louder first shot after the suppressor has been left standing, comes from the oxygen-rich air inside the can igniting with the muzzle gases and is influenced by the powder and charge you choose. Finally, barrel length is a real variable rather than a footnote: subsonic loads with fast powders reach peak velocity in a short barrel and can even lose velocity in a very long one, which is why each combination page shows the velocity across barrel lengths instead of a single number.

How to read these tables

Open any combination to see every suitable powder with its minimum and maximum charge, fill ratio, calculated peak pressure against the CIP or SAAMI limit for the cartridge, muzzle velocity and the velocity curve over barrel length. Units follow your measurement preference when you are signed in; visitors who are not signed in see imperial units on the English site and metric units on the German site. Exact charge weights require an access licence. As with all reloading data — calculated, published or shared by other reloaders — these figures are reference information, not an instruction to fire a specific charge in your firearm. Start below the listed maximum, work up in small increments, watch for pressure signs, and verify velocity over a chronograph before you rely on a load being subsonic.