Load data for 7.62 x 39 (M43) Russian + .311 | 90gr | Inceptor SRR

7.62 x 39 (M43) Russian cartridge drawing
Inceptor logo

Load Specifications

Bullet Manufacturer:Inceptor
Bullet Weight:90 gr
Bullet Diameter:0.311"
Bullet Length:<<locked>>
Case Length (l3):1.523"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:35.5 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:20"
Max. allowed Pressure:51,488 psi
Recommended Twist Rate:1:12.0

Load data in caliber 7.62 x 39 (M43) Russian with .311 | 90gr | Inceptor SRR bullet and 7 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Hodgdon LilGun, Lovex S040 and ADI AR 2205.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 20"

PowderChargeFRMaxP%V(0)z
ADI AR 2205<<locked>>96%44,193 psi86%2549 fps97.1%
Hodgdon LilGun<<locked>>92%45,295 psi88%2756 fps100%
Hodgdon TrailBossᴾ<<locked>>100%23,772 psi46%1627 fps100%
Lovex S040<<locked>>90%45,237 psi88%2605 fps99.8%
ReloadSwiss RS 14ᴾ<<locked>>100%22,887 psi44%1667 fps100%
SNPE Vectan BA6 1/2ᴾ<<locked>>100%32,648 psi63%2382 fps99.8%
Vihtavuori N110ᴾ<<locked>>100%41,945 psi81%2612 fps99.9%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 20"

PowderChargeFRMaxP%V(0)z
ADI AR 220521.4 gr90%36,840 psi72%2421 fps95.2%
Hodgdon LilGun20.8 gr80%29,254 psi57%2461 fps98.6%
Hodgdon TrailBoss<<locked>>80%16,926 psi33%1453 fps100%
Lovex S04017.8 gr80%33,504 psi65%2392 fps98.2%
ReloadSwiss RS 14<<locked>>80%16,447 psi32%1490 fps100%
SNPE Vectan BA6 1/2<<locked>>82%19,957 psi39%2044 fps95.6%
Vihtavuori N110<<locked>>80%22,698 psi44%2185 fps95.2%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 7 powders for 7.62 x 39 (M43) Russian loaded with the .311 | 90gr | Inceptor SRR. Hodgdon LilGun delivers the highest muzzle velocity at 2,756 fps; across all powders the maximum-charge window runs from 1,627 fps to 2,756 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 7 of the 7 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (355 MPa), the top charges use 44–88 %, leaving at least 12 % headroom. The 90.0 gr projectile in 0.311" calls for a 1:12.0 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, ReloadSwiss RS 14, SNPE Vectan BA6 1/2 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Hodgdon LilGun, Lovex S040, ADI AR 2205 rank at the top here: for 7.62 x 39 (M43) Russian with the .311 | 90gr | Inceptor SRR they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data