Load data for .45 Colt + .452 | 118gr | Inceptor ARX Prefered Defense

.45 Colt cartridge drawing
Inceptor logo

Load Specifications

Bullet Manufacturer:Inceptor
Bullet Weight:118 gr
Bullet Diameter:0.452"
Bullet Length:<<locked>>
Case Length (l3):1.266"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:41.6 Grains of Water
Primer Size:Large Pistol Magnum (LPM)
Barrel Length:5.5"
Max. allowed Pressure:15,954 psi

Load data in caliber .45 Colt with .452 | 118gr | Inceptor ARX Prefered Defense bullet and 5 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Hodgdon TrailBoss.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 60% and propellant combustion ≥ 80%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 5.5"

PowderChargeFRMaxP%V(0)z
Baschieri & Pellagri 102 Pistol²<<locked>>72%14,127 psi89%1316 fps99.3%
Hodgdon TrailBossᴾ<<locked>>100%11,893 psi75%1184 fps99.7%
ReloadSwiss RS 14ᴾ<<locked>>100%10,994 psi69%1168 fps96.5%
ReloadSwiss RS 20*²<<locked>>64%14,301 psi90%1375 fps89.7%
Vihtavuori N32C Tin Star²<<locked>>76%13,402 psi84%1237 fps100%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 5.5"

PowderChargeFRMaxP%V(0)z
Baschieri & Pellagri 102 Pistol²<<locked>>60%10,312 psi65%1158 fps96.3%
Hodgdon TrailBoss*²5.1 gr60%6,135 psi38%869 fps92.4%
ReloadSwiss RS 14*²<<locked>>60%5,903 psi37%856 fps86.4%
ReloadSwiss RS 20*²<<locked>>60%12,691 psi80%1302 fps87.2%
Vihtavuori N32C Tin Star²<<locked>>60%9,195 psi58%1070 fps99.9%

Recommended = one of the top powders for this cartridge and bullet combination.

* not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

² fill rate low - you might want to consider using a filler to ensure proper ignition.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 5 powders for .45 Colt loaded with the .452 | 118gr | Inceptor ARX Prefered Defense. ReloadSwiss RS 20 delivers the highest muzzle velocity at 1,375 fps; across all powders the maximum-charge window runs from 1,168 fps to 1,375 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 2 of the 5 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (110 MPa), the top charges use 69–90 %, leaving at least 10 % headroom. Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Hodgdon TrailBoss rank at the top here: for .45 Colt with the .452 | 118gr | Inceptor ARX Prefered Defense they combine a high case fill with complete burn and sit in the upper velocity band. As outliers, ReloadSwiss RS 20 burn incompletely and react more sensitively to barrel length and temperature. Hodgdon TrailBoss, ReloadSwiss RS 14, Vihtavuori N32C Tin Star stay subsonic at start load. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data