Load data for .45-70 Govt. + .458 | 250gr | CutEdge DGBR-HP

.45-70 Govt. cartridge drawing
Cutting Edge logo

Load Specifications

Bullet Manufacturer:Cutting Edge
Bullet Weight:250 gr
Bullet Diameter:0.458"
Bullet Length:<<locked>>
Case Length (l3):2.105"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:79 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:24"
Max. allowed Pressure:31,908 psi

Load data in caliber .45-70 Govt. with .458 | 250gr | CutEdge DGBR-HP bullet and 4 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are SNPE Vectan BA6 1/2, ReloadSwiss RS 14 and Hodgdon TrailBoss.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Hodgdon TrailBossᴾ<<locked>>100%26,049 psi82%1486 fps100%
Lovex S053<<locked>>86%28,195 psi88%2146 fps96.3%
ReloadSwiss RS 14ᴾ<<locked>>100%25,034 psi78%1516 fps100%
SNPE Vectan BA6 1/2<<locked>>88%28,369 psi89%2080 fps100%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Hodgdon TrailBoss14.5 gr80%18,768 psi59%1329 fps100%
Lovex S053<<locked>>84%26,672 psi84%2106 fps95.7%
ReloadSwiss RS 1414.7 gr80%17,970 psi56%1355 fps100%
SNPE Vectan BA6 1/235.2 gr80%22,669 psi71%1949 fps99.7%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 4 powders for .45-70 Govt. loaded with the .458 | 250gr | CutEdge DGBR-HP. Lovex S053 delivers the highest muzzle velocity at 2,146 fps; across all powders the maximum-charge window runs from 1,486 fps to 2,146 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 4 of the 4 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (220 MPa), the top charges use 78–89 %, leaving at least 11 % headroom. Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. SNPE Vectan BA6 1/2, ReloadSwiss RS 14, Hodgdon TrailBoss rank at the top here: for .45-70 Govt. with the .458 | 250gr | CutEdge DGBR-HP they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data