Load data for .303 Savage + .308 | 165gr | RWS Kegelspitz

.303 Savage cartridge drawing
RWS logo

Load Specifications

Bullet Manufacturer:RWS
Bullet Weight:165 gr
Bullet Diameter:0.308"
Bullet Length:<<locked>>
Case Length (l3):2.014"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:45 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:22"
Max. allowed Pressure:39,160 psi
Recommended Twist Rate:1:17.0

Load data in caliber .303 Savage with .308 | 165gr | RWS Kegelspitz bullet and 14 powders. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 22"

PowderChargeFRMaxP%V(0)z
Accurate 2015<<locked>>90%33,997 psi87%2100 fps97.5%
Accurate 2495ᴾ<<locked>>100%34,200 psi87%2182 fps98%
Alliant AR-Comp<<locked>>94%35,404 psi90%2198 fps99.6%
Alliant Reloder-10x<<locked>>86%34,882 psi89%2126 fps98.7%
Baschieri & Pellagri 106<<locked>>82%33,489 psi86%2028 fps95.9%
Hodgdon TrailBossᴾ<<locked>>100%31,575 psi81%1378 fps100%
IMR 3031<<locked>>94%33,837 psi86%2169 fps96.3%
IMR 4198<<locked>>84%35,012 psi89%2080 fps99.2%
Norma 200<<locked>>82%34,838 psi89%2110 fps99.1%
ReloadSwiss RS 14ᴾ<<locked>>100%31,343 psi80%1411 fps100%
SNPE Vectan SP 3<<locked>>84%33,417 psi85%2080 fps96.4%
Vihtavuori N130<<locked>>86%33,518 psi86%2051 fps98.1%
Vihtavuori N133<<locked>>92%34,795 psi89%2083 fps97.4%
Vihtavuori N135<<locked>>98%34,505 psi88%2159 fps97.8%

Start Load - Barrel Length: 22"

PowderChargeFRMaxP%V(0)z
Accurate 2015<<locked>>84%28,036 psi72%1975 fps95.3%
Accurate 2495<<locked>>92%26,150 psi67%2011 fps95.2%
Alliant AR-Comp<<locked>>80%23,177 psi59%1896 fps95.3%
Alliant Reloder-10x<<locked>>80%28,950 psi74%2001 fps97%
Baschieri & Pellagri 106<<locked>>80%31,662 psi81%1988 fps95.2%
Hodgdon TrailBoss<<locked>>80%23,395 psi60%1230 fps100%
IMR 3031<<locked>>92%31,923 psi82%2126 fps95.5%
IMR 4198<<locked>>80%31,285 psi80%2005 fps98.4%
Norma 200<<locked>>80%32,793 psi84%2070 fps98.8%
ReloadSwiss RS 14<<locked>>80%22,960 psi59%1257 fps100%
SNPE Vectan SP 3<<locked>>82%31,459 psi80%2037 fps95.6%
Vihtavuori N130<<locked>>80%28,021 psi72%1932 fps96.3%
Vihtavuori N133<<locked>>86%29,138 psi74%1965 fps95.4%
Vihtavuori N135<<locked>>92%28,558 psi73%2028 fps95.6%

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 14 powders for .303 Savage loaded with the .308 | 165gr | RWS Kegelspitz. Alliant AR-Comp delivers the highest muzzle velocity at 2,198 fps; across all powders the maximum-charge window runs from 1,378 fps to 2,198 fps. Accurate 2495 gives the best case fill at 100 %, and 14 of the 14 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (270 MPa), the top charges use 80–90 %, leaving at least 10 % headroom. The 165.0 gr projectile in 0.308" calls for a 1:17.0 twist; slower twists will usually not stabilise this weight. Accurate 2495, Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data