Load data for .300 AAC Blackout + .311 | 130gr | CutEdge ESP Raptor

.300 AAC Blackout cartridge drawing
Cutting Edge logo

Load Specifications

Bullet Manufacturer:Cutting Edge
Bullet Weight:130 gr
Bullet Diameter:0.311"
Bullet Length:<<locked>>
Case Length (l3):1.367"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:25.1 Grains of Water
Primer Size:Small Rifle (SR)
Barrel Length:16"
Max. allowed Pressure:50,763 psi
Recommended Twist Rate:1:15.0

Load data in caliber .300 AAC Blackout with .311 | 130gr | CutEdge ESP Raptor bullet and 7 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Hodgdon LilGun, Vihtavuori N110 and Lovex S040.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 16"

PowderChargeFRMaxP%V(0)z
ADI AR 2205<<locked>>98%44,628 psi88%1936 fps97.1%
Hodgdon LilGun<<locked>>94%45,121 psi89%2096 fps100%
Hodgdon TrailBossᴾ<<locked>>100%23,598 psi46%1181 fps100%
Lovex S040<<locked>>90%44,425 psi88%1952 fps99.8%
ReloadSwiss RS 14ᴾ<<locked>>100%23,032 psi45%1214 fps100%
SNPE Vectan BA6 1/2ᴾ<<locked>>100%31,502 psi62%1778 fps99.7%
Vihtavuori N110ᴾ<<locked>>100%39,914 psi79%1946 fps99.8%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 16"

PowderChargeFRMaxP%V(0)z
ADI AR 2205<<locked>>92%37,333 psi74%1834 fps95.3%
Hodgdon LilGun14.7 gr80%27,862 psi55%1831 fps98.3%
Hodgdon TrailBoss<<locked>>80%17,361 psi34%1060 fps100%
Lovex S04012.6 gr80%32,822 psi65%1778 fps98.2%
ReloadSwiss RS 14<<locked>>80%16,172 psi32%1070 fps100%
SNPE Vectan BA6 1/2<<locked>>82%19,595 psi39%1519 fps95.6%
Vihtavuori N11012.1 gr80%22,089 psi44%1621 fps95.1%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 7 powders for .300 AAC Blackout loaded with the .311 | 130gr | CutEdge ESP Raptor. Hodgdon LilGun delivers the highest muzzle velocity at 2,096 fps; across all powders the maximum-charge window runs from 1,181 fps to 2,096 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 7 of the 7 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (350 MPa), the top charges use 45–89 %, leaving at least 11 % headroom. The 130.0 gr projectile in 0.311" calls for a 1:15.0 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, ReloadSwiss RS 14, SNPE Vectan BA6 1/2 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Hodgdon LilGun, Vihtavuori N110, Lovex S040 rank at the top here: for .300 AAC Blackout with the .311 | 130gr | CutEdge ESP Raptor they combine a high case fill with complete burn and sit in the upper velocity band. Hodgdon TrailBoss, ReloadSwiss RS 14 stay subsonic at start load. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data