Load data for .30 Rem. + .308 | 150gr | Hornady InterLock RN

.30 Rem. cartridge drawing
Hornady logo

Load Specifications

Bullet Manufacturer:Hornady
Bullet Weight:150 gr
Bullet Diameter:0.308"
Bullet Length:<<locked>>
Case Length (l3):2.049"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:45.8 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:22"
Max. allowed Pressure:40,611 psi
Recommended Twist Rate:1:15.0

Load data in caliber .30 Rem. with .308 | 150gr | Hornady InterLock RN bullet and 13 powders. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 22"

PowderChargeFRMaxP%V(0)z
Accurate 2015<<locked>>94%35,085 psi86%2221 fps96.6%
ADI AR 2207<<locked>>84%36,419 psi90%2234 fps100%
Alliant AR-Comp<<locked>>98%36,709 psi90%2323 fps99.2%
Alliant Reloder-10x<<locked>>90%36,143 psi89%2257 fps98.1%
Alliant Reloder-7<<locked>>82%35,708 psi88%2185 fps98.3%
Hodgdon TrailBossᴾ<<locked>>100%30,951 psi76%1440 fps100%
IMR 4198<<locked>>86%34,679 psi85%2172 fps98.4%
Norma 200<<locked>>86%36,013 psi89%2238 fps98.7%
ReloadSwiss RS 14ᴾ<<locked>>100%30,618 psi75%1473 fps100%
Vihtavuori N120<<locked>>84%36,651 psi90%2201 fps100%
Vihtavuori N130<<locked>>90%35,259 psi87%2182 fps97.5%
Vihtavuori N133<<locked>>96%36,579 psi90%2211 fps96.7%
Vihtavuori N135ᴾ<<locked>>100%33,533 psi83%2234 fps96.2%

Start Load - Barrel Length: 22"

PowderChargeFRMaxP%V(0)z
Accurate 2015<<locked>>90%31,096 psi77%2139 fps95.3%
ADI AR 2207<<locked>>80%32,140 psi79%2149 fps99.7%
Alliant AR-Comp<<locked>>86%25,556 psi63%2051 fps95%
Alliant Reloder-10x<<locked>>82%28,268 psi70%2083 fps95.5%
Alliant Reloder-7<<locked>>80%33,663 psi83%2142 fps97.8%
Hodgdon TrailBoss<<locked>>80%22,872 psi56%1286 fps100%
IMR 4198<<locked>>80%29,269 psi72%2051 fps96.7%
Norma 200<<locked>>80%30,052 psi74%2116 fps97.1%
ReloadSwiss RS 14<<locked>>80%22,423 psi55%1312 fps100%
Vihtavuori N120<<locked>>80%32,387 psi80%2126 fps100%
Vihtavuori N130<<locked>>84%29,153 psi72%2054 fps95.5%
Vihtavuori N133<<locked>>92%32,503 psi80%2133 fps95.4%
Vihtavuori N135<<locked>>98%31,589 psi78%2192 fps95.4%

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 13 powders for .30 Rem. loaded with the .308 | 150gr | Hornady InterLock RN. Alliant AR-Comp delivers the highest muzzle velocity at 2,323 fps; across all powders the maximum-charge window runs from 1,440 fps to 2,323 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 13 of the 13 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (280 MPa), the top charges use 75–90 %, leaving at least 10 % headroom. The 150.0 gr projectile in 0.308" calls for a 1:15.0 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, ReloadSwiss RS 14, Vihtavuori N135 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data