Load data for .222 Rem. + .224 | 55gr | CutEdge MTH

.222 Rem. cartridge drawing
Cutting Edge logo

Load Specifications

Bullet Manufacturer:Cutting Edge
Bullet Weight:55 gr
Bullet Diameter:0.224"
Bullet Length:<<locked>>
Case Length (l3):1.7"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:27.9 Grains of Water
Primer Size:Small Rifle (SR)
Barrel Length:24"
Max. allowed Pressure:53,664 psi
Recommended Twist Rate:1:9.0

Load data in caliber .222 Rem. with .224 | 55gr | CutEdge MTH bullet and 26 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Norma 200, ADI AR 2207 and ReloadSwiss RS 36.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate 1680<<locked>>90%47,703 psi89%2946 fps98.9%
Accurate 2015ᴾ<<locked>>100%39,218 psi73%2877 fps96.4%
Accurate LT-30<<locked>>96%48,283 psi90%2940 fps96.7%
ADI AR 2205<<locked>>82%47,848 psi89%2854 fps100%
ADI AR 2207<<locked>>94%45,905 psi86%3012 fps100%
Alliant AR-Compᴾ<<locked>>100%37,347 psi70%2892 fps98%
Alliant Reloder-10xᴾ<<locked>>100%46,325 psi86%3033 fps98.8%
Alliant Reloder-7<<locked>>92%45,092 psi84%2954 fps99%
Baschieri & Pellagri 106<<locked>>96%46,021 psi86%2912 fps96.7%
Hodgdon H4198<<locked>>94%46,775 psi87%2933 fps95.7%
Hodgdon TrailBossᴾ<<locked>>100%30,066 psi56%1875 fps100%
IMR 4198<<locked>>98%45,847 psi85%2984 fps99.3%
IMR 4227<<locked>>88%47,210 psi88%2947 fps99.9%
Lovex D060<<locked>>82%47,993 psi89%2994 fps99.4%
Lovex D063<<locked>>82%48,399 psi90%2953 fps99.7%
Lovex S053<<locked>>88%45,788 psi85%2908 fps100%
Norma 200<<locked>>96%45,687 psi85%3017 fps99.3%
ReloadSwiss RS 14ᴾ<<locked>>100%29,747 psi55%1912 fps100%
ReloadSwiss RS 36<<locked>>88%46,383 psi86%2972 fps99.8%
Shooters World Buffalo Rifle<<locked>>82%47,993 psi89%2994 fps99.4%
Shooters World SOCOM<<locked>>82%48,399 psi90%2953 fps99.7%
SNPE Vectan BA6 1/2<<locked>>92%46,630 psi87%2768 fps100%
SNPE Vectan SP 3ᴾ<<locked>>100%47,718 psi89%3041 fps97.4%
Vihtavuori N110<<locked>>84%47,834 psi89%2878 fps100%
Vihtavuori N120<<locked>>96%45,701 psi85%2957 fps100%
Vihtavuori N130ᴾ<<locked>>100%43,192 psi80%2914 fps98.1%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate 1680<<locked>>80%34,243 psi64%2677 fps95.8%
Accurate 2015<<locked>>98%36,811 psi69%2825 fps95.6%
Accurate LT-30<<locked>>92%42,859 psi80%2841 fps95.4%
ADI AR 2205<<locked>>80%45,049 psi84%2808 fps100%
ADI AR 220716.2 gr80%29,298 psi55%2655 fps98.1%
Alliant AR-Comp<<locked>>94%30,371 psi57%2727 fps95.6%
Alliant Reloder-10x<<locked>>88%31,328 psi58%2720 fps95%
Alliant Reloder-7<<locked>>80%30,719 psi57%2637 fps95.2%
Baschieri & Pellagri 106<<locked>>92%40,524 psi76%2810 fps95.2%
Hodgdon H4198<<locked>>92%44,019 psi82%2883 fps95%
Hodgdon TrailBoss<<locked>>80%21,538 psi40%1673 fps100%
IMR 4198<<locked>>84%30,501 psi57%2634 fps95.4%
IMR 4227<<locked>>80%36,695 psi68%2741 fps98.8%
Lovex D060<<locked>>80%45,194 psi84%2941 fps99%
Lovex D063<<locked>>80%45,527 psi85%2904 fps99.5%
Lovex S053<<locked>>80%35,795 psi67%2718 fps100%
Norma 20017.8 gr84%30,922 psi58%2699 fps95.8%
ReloadSwiss RS 14<<locked>>80%21,074 psi39%1708 fps100%
ReloadSwiss RS 3616.8 gr80%35,766 psi67%2760 fps98.5%
Shooters World Buffalo Rifle<<locked>>80%45,194 psi84%2941 fps99%
Shooters World SOCOM<<locked>>80%45,527 psi85%2904 fps99.5%
SNPE Vectan BA6 1/2<<locked>>80%33,634 psi63%2546 fps100%
SNPE Vectan SP 3<<locked>>94%39,044 psi73%2871 fps95.2%
Vihtavuori N110<<locked>>80%42,656 psi79%2795 fps100%
Vihtavuori N120<<locked>>80%27,485 psi51%2569 fps98.5%
Vihtavuori N130<<locked>>92%33,765 psi63%2714 fps95.5%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 44 powders for .222 Rem. loaded with the .224 | 55gr | CutEdge MTH. SNPE Vectan SP 10 delivers the highest muzzle velocity at 3,063 fps; across all powders the maximum-charge window runs from 1,875 fps to 3,063 fps. Accurate 2015 gives the best case fill at 100 %, and 44 of the 44 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (370 MPa), the top charges use 51–90 %, leaving at least 10 % headroom. The 55.0 gr projectile in 0.224" calls for a 1:9.0 twist; slower twists will usually not stabilise this weight. Accurate 2015, Accurate 2460, Accurate 2495 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Norma 200, ADI AR 2207, ReloadSwiss RS 36 rank at the top here: for .222 Rem. with the .224 | 55gr | CutEdge MTH they combine a high case fill with complete burn and sit in the upper velocity band. As outliers, Accurate 2460, Accurate 2495, Accurate LT-32 burn incompletely and react more sensitively to barrel length and temperature. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data