Subsonic load data for .30-06 Spring. + .308 | 220gr | Sierra MatchKing

.30-06 Spring. cartridge drawing
Sierra logo

Load Specifications

Bullet Manufacturer:Sierra
Bullet Weight:220 gr
Bullet Diameter:0.308"
Bullet Length:<<locked>>
Case Length (l3):2.494"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:68.2 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:24"
Max. allowed Pressure:58,740 psi
Recommended Twist Rate:1:11.0

Load data in caliber .30-06 Spring. with .308 | 220gr | Sierra MatchKing bullet and 7 powders. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 33% and propellant combustion ≥ 80%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
ADI APS 350²<<locked>>33%19,348 psi33%1109 fps100%
Baschieri & Pellagri 102 Pistol²<<locked>>33%16,201 psi28%1086 fps100%
Hodgdon TrailBoss²<<locked>>61%18,971 psi32%1112 fps100%
ReloadSwiss RS 14²<<locked>>57%17,680 psi30%1102 fps100%
SNPE Vectan Tubal 5000*²<<locked>>33%7,934 psi14%1099 fps80.9%
Vihtavuori N135*²<<locked>>33%7,585 psi13%1099 fps81%
Vihtavuori N32C Tin Star²<<locked>>41%19,624 psi33%1112 fps100%

Start Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
ADI APS 350²<<locked>>33%19,348 psi33%1109 fps100%
Baschieri & Pellagri 102 Pistol²<<locked>>33%16,201 psi28%1086 fps100%
Hodgdon TrailBoss²<<locked>>33%9,326 psi16%820 fps100%
ReloadSwiss RS 14²<<locked>>33%9,369 psi16%840 fps100%
SNPE Vectan Tubal 5000*²<<locked>>33%7,934 psi14%1099 fps80.9%
Vihtavuori N135*²<<locked>>33%7,585 psi13%1099 fps81%
Vihtavuori N32C Tin Star²<<locked>>33%15,069 psi26%994 fps100%

* not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

² fill rate low - you might want to consider using a filler to ensure proper ignition.

<<locked>> you need an access license to unlock this data.

Subsonic loads are filtered so the start load is at least 220 m/s and the maximum load does not exceed the speed of sound (≈343 m/s).

This overview compares 7 powders for .30-06 Spring. loaded with the .308 | 220gr | Sierra MatchKing in the subsonic range. Hodgdon TrailBoss delivers the highest muzzle velocity at 1,112 fps; across all powders the maximum-charge window runs from 1,086 fps to 1,112 fps. Hodgdon TrailBoss gives the best case fill at 61 %, and 0 of the 7 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (405 MPa), the top charges use 13–33 %, leaving at least 67 % headroom. The 220.0 gr projectile in 0.308" calls for a 1:11.0 twist; slower twists will usually not stabilise this weight. ReloadSwiss RS 70, Alliant Power Pro 2000-MR, Hodgdon Superformance rank at the top here: for .30-06 Spring. with the .308 | 220gr | Sierra MatchKing they combine a high case fill with complete burn and sit in the upper velocity band. As outliers, SNPE Vectan Tubal 5000, Vihtavuori N135 burn incompletely and react more sensitively to barrel length and temperature. ADI APS 350, Baschieri & Pellagri 102 Pistol, Hodgdon TrailBoss stay subsonic at start load. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All subsonic load data