Load data for 9 mm Browning Court (.380 ACP) + .355 | 90gr | CutEdge HGHP

Recommended Powder(s): none

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.355 \| 90gr \| CutEdge HGHP
Manufacturer SKU:	HGHP 9MM 90
Bullet Weight:	90gr \| 5.8g
Bullet Diameter:	0.355" \| 9.02mm
Bullet Length:	0.609" \| 15.5mm
Caliber:	9 mm Browning Court (.380 ACP) load data
Case Length (l3):	0.681" \| 17.3mm
Cartridge Length (C.O.L.):	0.969" \| 24.6mm
Seated Depth:	0.321" \| 8.1mm
Shank Seated Depth:	0.321" \| 8.1mm
Case Capacity:	12.2 Grains of Water \| 0.79 cm³
Primer Size:	Small Pistol (SP)
Max. allowed Pressure:	19580 psi \| 1350 bar
LID:	LID_B8533_C1213
Last updated:	2025-01-01

Load data for 48 loads in caliber 9 mm Browning Court (.380 ACP) with .355 | 90gr | CutEdge HGHP bullet and 24 powders such as none. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
[ADI AP 70N]*	<<locked>>	90%	16520	84%	**5	86%
ADI APS 350	<<locked>>	76%	16114	82%	**7	100%
ADI APS 450	<<locked>>	77%	15345	78%	**0	100%
ADI AS 30	<<locked>>	93%	17361	89%	**2	98%
ADI AS 50N	<<locked>>	90%	16520	84%	**9	92%
Accurate Solo 1000	<<locked>>	87%	16302	83%	**3	92%
[Baschieri & Pellagri 100]*	<<locked>>	94%	15505	79%	**3	89%
Hodgdon Clays	<<locked>>	76%	15896	81%	**7	100%
[Hodgdon HP38]*	<<locked>>	72%	16998	87%	**6	88%
Hodgdon TiteGroup	<<locked>>	64%	16969	87%	**6	95%
[Hodgdon Universal]*	<<locked>>	94%	14779	75%	**9	84%
[Lovex S011]*	<<locked>>	77%	16056	82%	**0	85%
[Maxam CSB 3]*	<<locked>>	91%	13445	69%	**0	87%
Maxam CSB 4	<<locked>>	92%	15766	80%	**9	93%
Maxam CSB 5	<<locked>>	89%	16433	84%	**6	99%
[Ramshot Zip]*	<<locked>>	72%	16288	83%	**2	86%
ReloadSwiss RS 12	<<locked>>	96%	13561	69%	**5	93%
Rottweil P 801	<<locked>>	92%	15780	81%	**4	98%
SNPE Vectan BA10	<<locked>>	72%	15331	78%	**0	100%
[Somchem S121]*	<<locked>>	65%	16578	85%	**2	83%
Vihtavuori N310	<<locked>>	76%	15795	81%	**2	100%
Vihtavuori N320	<<locked>>	96%	15360	78%	**2	93%
Vihtavuori N32C Tin Star	<<locked>>	97%	8354	43%	**9	91%
[Winchester 231]*	<<locked>>	80%	16288	83%	**2	86%

Max Load - Barrel Length: 5.50''

Powder	Charge	FR	MaxP	%	V(0)	z
[ADI AP 70N]*	<<locked>>	79%	13169	67%	**3	82%
[ADI APS 350]²	<<locked>>	59%	10936	56%	**9	99%
ADI APS 450	<<locked>>	62%	10747	55%	**9	97%
[ADI AS 30]*	<<locked>>	62%	8920	46%	**9	89%
[ADI AS 50N]*	<<locked>>	62%	9239	47%	**9	81%
[Accurate Solo 1000]*	<<locked>>	65%	10225	52%	**2	84%
[Baschieri & Pellagri 100]*	<<locked>>	74%	10051	51%	**9	80%
[Hodgdon Clays]²	<<locked>>	59%	10747	55%	**6	98%
[Hodgdon HP38]*	<<locked>>	62%	12966	66%	**0	83%
[Hodgdon TiteGroup]²	<<locked>>	59%	14243	73%	**0	93%
[Hodgdon Universal]*	<<locked>>	88%	13169	67%	**3	82%
[Lovex S011]*	<<locked>>	71%	13967	71%	**4	83%
[Maxam CSB 3]*	<<locked>>	77%	10312	53%	**1	81%
[Maxam CSB 4]*	<<locked>>	64%	8427	43%	**6	81%
[Maxam CSB 5]²	<<locked>>	59%	8412	43%	**9	91%
[Ramshot Zip]*	<<locked>>	62%	12372	63%	**7	81%
[ReloadSwiss RS 12]*	<<locked>>	72%	8311	42%	**5	82%
[Rottweil P 801]*	<<locked>>	63%	8050	41%	**2	86%
SNPE Vectan BA10	<<locked>>	65%	12894	66%	**4	99%
[Somchem S121]*	<<locked>>	62%	14953	76%	**2	81%
Vihtavuori N310	<<locked>>	62%	10849	55%	**8	99%
[Vihtavuori N320]*	<<locked>>	68%	8586	44%	**9	81%
[Vihtavuori N32C Tin Star]*	<<locked>>	89%	7252	37%	**9	88%
[Winchester 231]*	<<locked>>	69%	12372	63%	**7	81%

Start Load - Barrel Length: 5.50''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data