Load data for 6.5 x 52 R + .257 | 87gr | Winchester Pointed Soft Point

6.5 x 52 R cartridge drawing
Winchester logo

Load Specifications

Bullet Manufacturer:Winchester
Bullet Weight:87 gr
Bullet Diameter:0.257"
Bullet Length:<<locked>>
Case Length (l3):2.047"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:37 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:23.62"
Max. allowed Pressure:35,534 psi
Recommended Twist Rate:1:10.5

Load data in caliber 6.5 x 52 R with .257 | 87gr | Winchester Pointed Soft Point bullet and 6 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Alliant AR-Comp, ReloadSwiss RS 14 and Hodgdon TrailBoss.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 23.62"

PowderChargeFRMaxP%V(0)z
Accurate 2495<<locked>>98%32,068 psi90%2579 fps96.4%
Alliant AR-Comp<<locked>>90%31,357 psi88%2552 fps98.1%
Alliant Reloder-10x<<locked>>82%30,603 psi86%2474 fps96.6%
Hodgdon TrailBossᴾ<<locked>>100%31,546 psi89%1713 fps100%
ReloadSwiss RS 14ᴾ<<locked>>100%31,415 psi88%1752 fps100%
Vihtavuori N130<<locked>>84%31,691 psi89%2441 fps96.6%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 23.62"

PowderChargeFRMaxP%V(0)z
Accurate 2495<<locked>>96%30,081 psi85%2530 fps95.6%
Alliant AR-Comp22.4 gr84%26,092 psi73%2392 fps95.6%
Alliant Reloder-10x<<locked>>80%28,805 psi81%2425 fps95.8%
Hodgdon TrailBoss7.4 gr80%23,003 psi65%1526 fps100%
ReloadSwiss RS 147.6 gr80%23,047 psi65%1565 fps100%
Vihtavuori N130<<locked>>80%27,833 psi78%2339 fps95%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 22 powders for 6.5 x 52 R loaded with the .257 | 87gr | Winchester Pointed Soft Point. Accurate 4064 delivers the highest muzzle velocity at 2,582 fps; across all powders the maximum-charge window runs from 1,713 fps to 2,582 fps. Accurate 4064 gives the best case fill at 100 %, and 22 of the 22 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (245 MPa), the top charges use 86–90 %, leaving at least 10 % headroom. The 87.0 gr projectile in 0.257" calls for a 1:10.5 twist; slower twists will usually not stabilise this weight. Accurate 4064, Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Alliant AR-Comp, ReloadSwiss RS 14, Hodgdon TrailBoss rank at the top here: for 6.5 x 52 R with the .257 | 87gr | Winchester Pointed Soft Point they combine a high case fill with complete burn and sit in the upper velocity band. As outliers, Accurate 2460, Accurate 4064, Hodgdon H322 burn incompletely and react more sensitively to barrel length and temperature. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data