Load data for 6 x 70 R + .243 | 105gr | Speer Spitzer Soft Point

6 x 70 R cartridge drawing
Speer logo

Load Specifications

Bullet Manufacturer:Speer
Bullet Weight:105 gr
Bullet Diameter:0.243"
Bullet Length:<<locked>>
Case Length (l3):2.75"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:39.9 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:25.6"
Max. allowed Pressure:37,710 psi
Recommended Twist Rate:1:10.0

Load data in caliber 6 x 70 R with .243 | 105gr | Speer Spitzer Soft Point bullet and 11 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Somchem S365, ReloadSwiss RS 14 and Hodgdon TrailBoss.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 25.6"

PowderChargeFRMaxP%V(0)z
Alliant Reloder-17<<locked>>86%34,084 psi90%2444 fps96.3%
Bofors RP3<<locked>>82%33,910 psi90%2382 fps97.2%
Hodgdon Hybrid 100V<<locked>>92%33,388 psi89%2372 fps96.1%
Hodgdon TrailBoss<<locked>>98%33,765 psi90%1608 fps100%
ReloadSwiss RS 14<<locked>>98%34,069 psi90%1647 fps100%
ReloadSwiss RS 60<<locked>>84%33,895 psi90%2451 fps98.7%
Rottweil R 903<<locked>>84%33,837 psi90%2372 fps96.8%
Somchem S355<<locked>>82%32,866 psi87%2333 fps96.2%
Somchem S365<<locked>>92%32,445 psi86%2411 fps97.4%
Vihtavuori N150<<locked>>84%33,228 psi88%2323 fps97.7%
Winchester 6.5 StaBALL<<locked>>88%34,098 psi90%2346 fps96.5%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 25.6"

PowderChargeFRMaxP%V(0)z
Alliant Reloder-17<<locked>>84%31,821 psi84%2385 fps95.3%
Bofors RP3<<locked>>80%31,517 psi84%2326 fps96.3%
Hodgdon Hybrid 100V<<locked>>90%31,459 psi83%2323 fps95.3%
Hodgdon TrailBoss8.6 gr80%25,889 psi69%1453 fps100%
ReloadSwiss RS 148.7 gr80%25,860 psi69%1483 fps100%
ReloadSwiss RS 60<<locked>>80%29,834 psi79%2343 fps97.1%
Rottweil R 903<<locked>>80%29,820 psi79%2277 fps95.3%
Somchem S355<<locked>>80%30,879 psi82%2287 fps95.4%
Somchem S36527.8 gr88%28,543 psi76%2306 fps95.6%
Vihtavuori N150<<locked>>80%29,341 psi78%2234 fps96.4%
Winchester 6.5 StaBALL<<locked>>86%31,908 psi85%2297 fps95.5%

Recommended = one of the top powders for this cartridge and bullet combination.

This overview compares 11 powders for 6 x 70 R loaded with the .243 | 105gr | Speer Spitzer Soft Point. ReloadSwiss RS 60 delivers the highest muzzle velocity at 2,451 fps; across all powders the maximum-charge window runs from 1,608 fps to 2,451 fps. Hodgdon TrailBoss gives the best case fill at 98 %, and 11 of the 11 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (260 MPa), the top charges use 86–90 %, leaving at least 10 % headroom. The 105.0 gr projectile in 0.243" calls for a 1:10.0 twist; slower twists will usually not stabilise this weight. Somchem S365, ReloadSwiss RS 14, Hodgdon TrailBoss rank at the top here: for 6 x 70 R with the .243 | 105gr | Speer Spitzer Soft Point they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data