Load Specifications
Load data in caliber .38 Special with .355 | 123gr | Geco SOFTPOINT bullet and 7 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Hodgdon TrailBoss and ReloadSwiss RS 14.
Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.
Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 60% and propellant combustion ≥ 80%. Use the sliders above the tables to adjust these thresholds.
Charge: Powder weight in grains. Start with the minimum load and work up carefully.
FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.
MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.
V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.
z (Powder Burn): Estimated propellant combustion percentage at bullet exit.
A valid access license is required to use the Personalized Load Calculator.
You can find more information in our FAQ: How can I use the Personalized Load Calculator?
Max Load - Barrel Length: 4"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Alliant Herco² | <<locked>> | 68% | 18,043 psi | 83% | 1027 fps | 96.2% |
| Baschieri & Pellagri 102 Pistol² | <<locked>> | 72% | 19,464 psi | 89% | 1010 fps | 100% |
| Hodgdon TrailBossᴾ | <<locked>> | 100% | 15,635 psi | 72% | 896 fps | 100% |
| ReloadSwiss RS 14ᴾ | <<locked>> | 100% | 14,272 psi | 66% | 892 fps | 100% |
| SNPE Vectan BA7 1/2*² | <<locked>> | 64% | 17,405 psi | 80% | 1007 fps | 87.5% |
| Vihtavuori N32C Tin Star² | <<locked>> | 76% | 18,014 psi | 83% | 932 fps | 100% |
| Vihtavuori N350*² | <<locked>> | 68% | 19,595 psi | 90% | 1079 fps | 91.3% |
Recommended = one of the top powders for this cartridge and bullet combination.
Start Load - Barrel Length: 4"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Alliant Herco*² | <<locked>> | 60% | 14,504 psi | 67% | 935 fps | 92.9% |
| Baschieri & Pellagri 102 Pistol² | <<locked>> | 60% | 14,011 psi | 64% | 896 fps | 100% |
| Hodgdon TrailBoss² | 3.2 gr | 60% | 7,295 psi | 34% | 656 fps | 98.5% |
| ReloadSwiss RS 14*² | 3.3 gr | 60% | 6,962 psi | 32% | 653 fps | 94.4% |
| SNPE Vectan BA7 1/2*² | <<locked>> | 60% | 15,708 psi | 72% | 965 fps | 85.5% |
| Vihtavuori N32C Tin Star² | <<locked>> | 60% | 12,009 psi | 55% | 801 fps | 100% |
| Vihtavuori N350*² | <<locked>> | 60% | 15,258 psi | 70% | 971 fps | 86.5% |
Recommended = one of the top powders for this cartridge and bullet combination.
* not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.
² fill rate low - you might want to consider using a filler to ensure proper ignition.
ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.
This overview compares 2 powders for .38 Special loaded with the .355 | 123gr | Geco SOFTPOINT. Hodgdon TrailBoss delivers the highest muzzle velocity at 896 fps; across all powders the maximum-charge window runs from 892 fps to 896 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 2 of the 2 powders fall inside the usable 80–100 % fill window.
Relative to the caliber's maximum pressure (150 MPa), the top charges use 66–72 %, leaving at least 28 % headroom. Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Hodgdon TrailBoss, ReloadSwiss RS 14 rank at the top here: for .38 Special with the .355 | 123gr | Geco SOFTPOINT they combine a high case fill with complete burn and sit in the upper velocity band. Hodgdon TrailBoss, ReloadSwiss RS 14 stay subsonic at start load. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.