Load data for .38 Short Colt + .355 | 80gr | Peregrine SD 9mm Short

Recommended Powder(s): none

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.355 \| 80gr \| Peregrine SD 9mm Short
Bullet Weight:	80gr \| 5.2g
Bullet Diameter:	0.355" \| 9.02mm
Bullet Length:	0.520" \| 13.2mm
Caliber:	.38 Short Colt load data
Case Length (l3):	0.755" \| 19.2mm
Cartridge Length (C.O.L.):	1.102" \| 28.0mm
Seated Depth:	0.173" \| 4.4mm
Shank Seated Depth:	0.122" \| 3.1mm
Case Capacity:	11.0 Grains of Water \| 0.71 cm³
Primer Size:	Small Pistol (SP)
Max. allowed Pressure:	13053 psi \| 900 bar
LID:	LID_B8176_C584
Last updated:	2025-01-01
Recommended Twist Rate:	1:27 - 1:23

Load data for 0 loads in caliber .38 Short Colt with .355 | 80gr | Peregrine SD 9mm Short bullet and 0 powders such as none. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
[ADI AP 70N]*	<<locked>>	74%	11676	89%	**40	85%
ADI AS 30	<<locked>>	75%	11719	90%	**4	97%
ADI AS 50N	<<locked>>	73%	11371	87%	**8	91%
Accurate Solo 1000	<<locked>>	70%	11589	89%	**5	92%
[Accurate Solo 1250]*	<<locked>>	84%	11458	88%	**8	83%
[Baschieri & Pellagri 100]*	<<locked>>	77%	11400	87%	**8	89%
Baschieri & Pellagri 103 Pistol	<<locked>>	78%	11356	87%	**14	90%
[Hodgdon Universal]*	<<locked>>	82%	11676	89%	**40	85%
[Hodgdon CFE Pistol]*	<<locked>>	83%	11719	90%	**17	83%
[Maxam CSB 1]*	<<locked>>	86%	11284	86%	**4	83%
Maxam CSB 2	<<locked>>	96%	11618	89%	**89	91%
[Maxam CSB 3]*	<<locked>>	80%	11719	90%	**01	89%
Maxam CSB 4	<<locked>>	75%	11414	87%	**1	93%
Maxam CSB 5	<<locked>>	69%	11008	84%	**4	99%
ReloadSwiss RS 12	<<locked>>	84%	11356	87%	**96	95%
Rottweil P 801	<<locked>>	75%	11400	87%	**73	97%
[SNPE Vectan BA9 1/2]*	<<locked>>	79%	11560	89%	**7	83%
Vihtavuori N310	<<locked>>	62%	11603	89%	**7	100%
Vihtavuori N320	<<locked>>	79%	11168	86%	**17	93%
[Vihtavuori N330]*	<<locked>>	84%	11632	89%	**30	84%
[Winchester 231]*	<<locked>>	64%	11443	88%	**1	85%

Max Load - Barrel Length: 5.50''

Powder	Charge	FR	MaxP	%	V(0)	z
[ADI AP 70N]*	<<locked>>	67%	9181	70%	**5	81%
ADI AS 30	<<locked>>	70%	10153	78%	**2	96%
[ADI AS 50N]*	<<locked>>	69%	9964	76%	**8	89%
Accurate Solo 1000	<<locked>>	68%	10820	83%	**5	91%
[Accurate Solo 1250]*	<<locked>>	79%	10124	78%	**2	80%
[Baschieri & Pellagri 100]*	<<locked>>	73%	10051	77%	**2	87%
[Baschieri & Pellagri 103 Pistol]*	<<locked>>	70%	8905	68%	**2	85%
[Hodgdon Universal]*	<<locked>>	74%	9181	70%	**5	81%
[Hodgdon CFE Pistol]*	<<locked>>	77%	10022	77%	**8	80%
[Maxam CSB 1]*	<<locked>>	82%	9993	77%	**5	80%
[Maxam CSB 2]*	<<locked>>	82%	7876	60%	**2	83%
[Maxam CSB 3]*	<<locked>>	74%	9689	74%	**8	86%
Maxam CSB 4	<<locked>>	71%	9979	76%	**8	90%
Maxam CSB 5	<<locked>>	64%	9529	73%	**5	97%
[ReloadSwiss RS 12]*	<<locked>>	71%	7397	57%	**5	87%
Rottweil P 801	<<locked>>	64%	7760	59%	**5	92%
[SNPE Vectan BA9 1/2]*	<<locked>>	75%	10298	79%	**1	80%
Vihtavuori N310	<<locked>>	60%	10747	82%	**1	100%
[Vihtavuori N320]*	<<locked>>	72%	9195	70%	**2	89%
[Vihtavuori N330]*	<<locked>>	79%	9848	75%	**1	81%
[Winchester 231]*	<<locked>>	61%	10240	78%	**8	83%

Start Load - Barrel Length: 5.50''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data