Load Specifications
Load data in caliber .32 H&R Mag. with .312 | 85gr | Speer JHP bullet and 6 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Hodgdon TrailBoss and ReloadSwiss RS 14.
Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.
Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 60% and propellant combustion ≥ 80%. Use the sliders above the tables to adjust these thresholds.
Charge: Powder weight in grains. Start with the minimum load and work up carefully.
FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.
MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.
V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.
z (Powder Burn): Estimated propellant combustion percentage at bullet exit.
A valid access license is required to use the Personalized Load Calculator.
You can find more information in our FAQ: How can I use the Personalized Load Calculator?
Max Load - Barrel Length: 4"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Alliant Herco*² | <<locked>> | 72% | 17,651 psi | 87% | 1070 fps | 94.1% |
| Baschieri & Pellagri 102 Pistol² | <<locked>> | 72% | 17,535 psi | 86% | 1030 fps | 100% |
| Hodgdon TrailBossᴾ | <<locked>> | 100% | 14,330 psi | 71% | 922 fps | 100% |
| ReloadSwiss RS 14ᴾ | <<locked>> | 100% | 13,155 psi | 65% | 912 fps | 99.6% |
| ReloadSwiss RS 20² | <<locked>> | 64% | 18,173 psi | 90% | 1102 fps | 96.6% |
| Vihtavuori N32C Tin Star | <<locked>> | 80% | 17,579 psi | 87% | 978 fps | 100% |
Recommended = one of the top powders for this cartridge and bullet combination.
Start Load - Barrel Length: 4"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Alliant Herco*² | <<locked>> | 60% | 13,169 psi | 65% | 945 fps | 89.1% |
| Baschieri & Pellagri 102 Pistol² | <<locked>> | 60% | 12,647 psi | 62% | 909 fps | 99.6% |
| Hodgdon TrailBoss² | 2.3 gr | 60% | 6,512 psi | 32% | 659 fps | 95.9% |
| ReloadSwiss RS 14*² | 2.4 gr | 60% | 6,295 psi | 31% | 656 fps | 90.6% |
| ReloadSwiss RS 20² | <<locked>> | 60% | 16,099 psi | 79% | 1053 fps | 95% |
| Vihtavuori N32C Tin Star² | <<locked>> | 60% | 11,139 psi | 55% | 827 fps | 100% |
Recommended = one of the top powders for this cartridge and bullet combination.
* not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.
² fill rate low - you might want to consider using a filler to ensure proper ignition.
ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.
This overview compares 6 powders for .32 H&R Mag. loaded with the .312 | 85gr | Speer JHP. ReloadSwiss RS 20 delivers the highest muzzle velocity at 1,102 fps; across all powders the maximum-charge window runs from 912 fps to 1,102 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 3 of the 6 powders fall inside the usable 80–100 % fill window.
Relative to the caliber's maximum pressure (140 MPa), the top charges use 65–90 %, leaving at least 10 % headroom. Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Hodgdon TrailBoss, ReloadSwiss RS 14 rank at the top here: for .32 H&R Mag. with the .312 | 85gr | Speer JHP they combine a high case fill with complete burn and sit in the upper velocity band. As outliers, Alliant Herco burn incompletely and react more sensitively to barrel length and temperature. Alliant Herco, Baschieri & Pellagri 102 Pistol, Hodgdon TrailBoss stay subsonic at start load. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.