Load data for .303 Savage + .308 | 150gr | CutEdge MTH

Recommended Powder(s): none

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.308 \| 150gr \| CutEdge MTH
Manufacturer SKU:	MTH 308 150
Bullet Weight:	150gr \| 9.7g
Bullet Diameter:	0.308" \| 7.82mm
Bullet Length:	1.242" \| 31.5mm
Caliber:	.303 Savage load data
Case Length (l3):	2.014" \| 51.2mm
Cartridge Length (C.O.L.):	2.482" \| 63.0mm
Seated Depth:	0.774" \| 19.7mm
Shank Seated Depth:	0.538" \| 13.7mm
Case Capacity:	45.0 Grains of Water \| 2.92 cm³
Primer Size:	Large Rifle (LR)
Max. allowed Pressure:	39160 psi \| 2700 bar
LID:	LID_B8478_C391
Last updated:	2025-01-01
Recommended Twist Rate:	1:12 - 1:10

Load data for 40 loads in caliber .303 Savage with .308 | 150gr | CutEdge MTH bullet and 20 powders such as none. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AR 2207	<<locked>>	87%	34766	89%	**05	100%
[ADI AR 2219]*	<<locked>>	89%	34229	87%	**01	93%
Accurate 2015	<<locked>>	97%	34969	89%	**21	97%
[Accurate 2495]*	<<locked>>	96%	25048	64%	**10	92%
Alliant AR-Comp	<<locked>>	96%	30966	79%	**88	97%
Alliant Reloder-10x	<<locked>>	92%	34287	88%	**21	97%
Alliant Reloder-7	<<locked>>	85%	35230	90%	**72	98%
[Baschieri & Pellagri 106]*	<<locked>>	89%	35157	90%	**42	94%
[Hodgdon H322]*	<<locked>>	95%	34766	89%	**15	93%
[Hodgdon H335]*	<<locked>>	91%	34896	89%	**21	92%
[Hodgdon H4198]*	<<locked>>	86%	35157	90%	**16	93%
IMR 4198	<<locked>>	90%	34809	89%	**69	98%
Norma 200	<<locked>>	89%	34272	88%	**11	98%
[Rottweil R 901]*	<<locked>>	97%	33286	85%	**75	92%
[SNPE Vectan SP 10]*	<<locked>>	90%	35012	89%	**24	92%
[SNPE Vectan Tubal 3000]*	<<locked>>	97%	33750	86%	**26	92%
[Somchem S335]*	<<locked>>	96%	31372	80%	**10	92%
Vihtavuori N120	<<locked>>	88%	34113	87%	**59	100%
Vihtavuori N130	<<locked>>	94%	34940	89%	**75	97%
[Vihtavuori N133]*	<<locked>>	96%	30023	77%	**70	94%

Max Load - Barrel Length: 23.60''

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AR 2207	<<locked>>	81%	29008	74%	**87	99%
[ADI AR 2219]*	<<locked>>	84%	28892	74%	**80	91%
[Accurate 2015]*	<<locked>>	82%	21901	56%	**13	90%
[Accurate 2495]*	<<locked>>	92%	21683	55%	**11	90%
[Alliant AR-Comp]*	<<locked>>	83%	20682	53%	**90	90%
[Alliant Reloder-10x]*	<<locked>>	81%	23902	61%	**78	93%
Alliant Reloder-7	<<locked>>	81%	30806	79%	**80	97%
[Baschieri & Pellagri 106]*	<<locked>>	81%	27340	70%	**69	91%
[Hodgdon H322]*	<<locked>>	89%	28268	72%	**67	90%
[Hodgdon H335]*	<<locked>>	88%	31589	81%	**49	90%
[Hodgdon H4198]*	<<locked>>	81%	30560	78%	**24	91%
IMR 4198	<<locked>>	81%	27470	70%	**01	95%
Norma 200	<<locked>>	81%	26847	69%	**47	96%
[Rottweil R 901]*	<<locked>>	94%	30081	77%	**06	90%
[SNPE Vectan SP 10]*	<<locked>>	86%	30705	78%	**33	90%
[SNPE Vectan Tubal 3000]*	<<locked>>	93%	30385	78%	**54	90%
[Somchem S335]*	<<locked>>	92%	27499	70%	**24	90%
Vihtavuori N120	<<locked>>	81%	27427	70%	**21	99%
[Vihtavuori N130]*	<<locked>>	81%	22960	59%	**96	92%
[Vihtavuori N133]*	<<locked>>	88%	23786	61%	**13	90%

Start Load - Barrel Length: 23.60''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data