Load data for .300 AAC Blackout + .308 | 125gr | Hornady SST

.300 AAC Blackout cartridge drawing
Hornady logo

Load Specifications

Bullet Manufacturer:Hornady
Bullet Weight:125 gr
Bullet Diameter:0.308"
Bullet Length:<<locked>>
Case Length (l3):1.367"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:25.1 Grains of Water
Primer Size:Small Rifle (SR)
Barrel Length:16"
Max. allowed Pressure:50,763 psi
Recommended Twist Rate:1:14.5

Load data in caliber .300 AAC Blackout with .308 | 125gr | Hornady SST bullet and 7 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Hodgdon LilGun, Lovex S040 and Vihtavuori N110.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 16"

PowderChargeFRMaxP%V(0)z
ADI AR 2205<<locked>>98%45,150 psi89%1975 fps96.7%
Hodgdon LilGun<<locked>>94%45,498 psi90%2142 fps100%
Hodgdon TrailBossᴾ<<locked>>100%24,294 psi48%1214 fps100%
Lovex S040<<locked>>90%44,193 psi87%1985 fps99.6%
ReloadSwiss RS 14ᴾ<<locked>>100%23,264 psi46%1237 fps100%
SNPE Vectan BA6 1/2ᴾ<<locked>>100%31,560 psi62%1811 fps99.5%
Vihtavuori N110ᴾ<<locked>>100%39,813 psi78%1982 fps99.6%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 16"

PowderChargeFRMaxP%V(0)z
ADI AR 2205<<locked>>94%39,943 psi79%1903 fps95.5%
Hodgdon LilGun14.8 gr80%28,065 psi55%1867 fps97.9%
Hodgdon TrailBoss<<locked>>80%17,622 psi35%1079 fps100%
Lovex S04012.7 gr80%32,909 psi65%1811 fps97.8%
ReloadSwiss RS 14<<locked>>80%17,013 psi34%1106 fps100%
SNPE Vectan BA6 1/2<<locked>>82%20,044 psi39%1552 fps95.3%
Vihtavuori N11012.5 gr82%23,902 psi47%1690 fps95.5%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 7 powders for .300 AAC Blackout loaded with the .308 | 125gr | Hornady SST. Hodgdon LilGun delivers the highest muzzle velocity at 2,142 fps; across all powders the maximum-charge window runs from 1,214 fps to 2,142 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 7 of the 7 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (350 MPa), the top charges use 46–90 %, leaving at least 10 % headroom. The 125.0 gr projectile in 0.308" calls for a 1:14.5 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, ReloadSwiss RS 14, SNPE Vectan BA6 1/2 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Hodgdon LilGun, Lovex S040, Vihtavuori N110 rank at the top here: for .300 AAC Blackout with the .308 | 125gr | Hornady SST they combine a high case fill with complete burn and sit in the upper velocity band. Hodgdon TrailBoss, ReloadSwiss RS 14 stay subsonic at start load. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data