Load data for .300 AAC Blackout + .308 | 125gr | Barnes X S

.300 AAC Blackout cartridge drawing
Barnes logo

Load Specifications

Bullet Manufacturer:Barnes
Bullet Weight:125 gr
Bullet Diameter:0.308"
Bullet Length:<<locked>>
Case Length (l3):1.367"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:25.1 Grains of Water
Primer Size:Small Rifle (SR)
Barrel Length:16"
Max. allowed Pressure:50,763 psi
Recommended Twist Rate:1:15.0

Load data in caliber .300 AAC Blackout with .308 | 125gr | Barnes X S bullet and 7 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Vihtavuori N110, Hodgdon LilGun and Lovex S040.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 16"

PowderChargeFRMaxP%V(0)z
ADI AR 2205<<locked>>96%45,716 psi90%1965 fps96.8%
Hodgdon LilGun<<locked>>90%43,192 psi85%2090 fps100%
Hodgdon TrailBossᴾ<<locked>>100%26,107 psi51%1220 fps100%
Lovex S040<<locked>>88%44,672 psi88%1972 fps99.6%
ReloadSwiss RS 14ᴾ<<locked>>100%25,280 psi50%1243 fps100%
SNPE Vectan BA6 1/2ᴾ<<locked>>100%34,432 psi68%1837 fps99.8%
Vihtavuori N110ᴾ<<locked>>100%43,308 psi85%2008 fps99.8%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 16"

PowderChargeFRMaxP%V(0)z
ADI AR 2205<<locked>>92%40,770 psi80%1896 fps95.6%
Hodgdon LilGun14.8 gr80%31,778 psi63%1909 fps98.8%
Hodgdon TrailBoss<<locked>>80%19,377 psi38%1089 fps100%
Lovex S04012.7 gr80%35,650 psi70%1837 fps98.4%
ReloadSwiss RS 14<<locked>>80%18,927 psi37%1112 fps100%
SNPE Vectan BA6 1/2<<locked>>80%21,683 psi43%1562 fps96.1%
Vihtavuori N11012.2 gr80%25,846 psi51%1699 fps96.2%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 7 powders for .300 AAC Blackout loaded with the .308 | 125gr | Barnes X S. Hodgdon LilGun delivers the highest muzzle velocity at 2,090 fps; across all powders the maximum-charge window runs from 1,220 fps to 2,090 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 7 of the 7 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (350 MPa), the top charges use 50–90 %, leaving at least 10 % headroom. The 125.0 gr projectile in 0.308" calls for a 1:15.0 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, ReloadSwiss RS 14, SNPE Vectan BA6 1/2 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Vihtavuori N110, Hodgdon LilGun, Lovex S040 rank at the top here: for .300 AAC Blackout with the .308 | 125gr | Barnes X S they combine a high case fill with complete burn and sit in the upper velocity band. Hodgdon TrailBoss, ReloadSwiss RS 14 stay subsonic at start load. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data