Load data for .30 Rem. + .308 | 110gr | Fox Classic Hunter

.30 Rem. cartridge drawing
Fox Bullets logo

Load Specifications

Bullet Manufacturer:Fox Bullets
Bullet Weight:110 gr
Bullet Diameter:0.308"
Bullet Length:<<locked>>
Case Length (l3):2.049"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:45.8 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:22"
Max. allowed Pressure:40,611 psi
Recommended Twist Rate:1:14.0

Load data in caliber .30 Rem. with .308 | 110gr | Fox Classic Hunter bullet and 8 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are ADI AR 2207, Vihtavuori N120 and SNPE Vectan BA6 1/2.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 22"

PowderChargeFRMaxP%V(0)z
ADI AR 2207<<locked>>92%34,795 psi86%2602 fps98%
Hodgdon TrailBossᴾ<<locked>>100%28,587 psi70%1683 fps100%
IMR 4227<<locked>>84%35,360 psi87%2507 fps96.8%
Lovex S053<<locked>>86%36,230 psi89%2533 fps99.5%
ReloadSwiss RS 14ᴾ<<locked>>100%27,847 psi69%1719 fps100%
ReloadSwiss RS 36<<locked>>86%36,434 psi90%2575 fps96.9%
SNPE Vectan BA6 1/2<<locked>>88%35,955 psi89%2415 fps100%
Vihtavuori N120<<locked>>92%35,201 psi87%2575 fps99%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 22"

PowderChargeFRMaxP%V(0)z
ADI AR 220725.8 gr84%27,238 psi67%2405 fps95.3%
Hodgdon TrailBoss<<locked>>80%20,436 psi50%1496 fps100%
IMR 4227<<locked>>80%31,270 psi77%2408 fps95.4%
Lovex S053<<locked>>80%30,487 psi75%2402 fps98.4%
ReloadSwiss RS 14<<locked>>80%20,030 psi49%1532 fps100%
ReloadSwiss RS 36<<locked>>82%31,995 psi79%2470 fps95.5%
SNPE Vectan BA6 1/221.6 gr80%28,935 psi71%2274 fps100%
Vihtavuori N12024.5 gr80%24,279 psi60%2283 fps95.1%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 8 powders for .30 Rem. loaded with the .308 | 110gr | Fox Classic Hunter. ADI AR 2207 delivers the highest muzzle velocity at 2,602 fps; across all powders the maximum-charge window runs from 1,683 fps to 2,602 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 8 of the 8 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (280 MPa), the top charges use 69–90 %, leaving at least 10 % headroom. The 110.0 gr projectile in 0.308" calls for a 1:14.0 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. ADI AR 2207, Vihtavuori N120, SNPE Vectan BA6 1/2 rank at the top here: for .30 Rem. with the .308 | 110gr | Fox Classic Hunter they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data