Load data for .260 PICRA + .264 | 155gr | Lapua Mega

Recommended Powder(s): none

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.264 \| 155gr \| Lapua Mega
Manufacturer SKU:	4PL6010 \| E471
Bullet Weight:	155gr \| 10.0g
Bullet Diameter:	0.264" \| 6.71mm
Bullet Length:	1.248" \| 31.7mm
Caliber:	.260 PICRA load data
Case Length (l3):	1.515" \| 38.5mm
Cartridge Length (C.O.L.):	2.404" \| 61.1mm
Seated Depth:	0.359" \| 9.1mm
Shank Seated Depth:	0.359" \| 9.1mm
Case Capacity:	38.6 Grains of Water \| 2.51 cm³
Primer Size:	Large Pistol (LP)
Max. allowed Pressure:	56565 psi \| 3900 bar
LID:	LID_B3125_C251
Last updated:	2025-01-01

Load data for 44 loads in caliber .260 PICRA with .264 | 155gr | Lapua Mega bullet and 22 powders such as none. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	66%	50372	89%	**19	100%
ADI APS 350	<<locked>>	74%	50821	90%	**78	100%
ADI APS 450	<<locked>>	72%	50154	89%	**81	100%
ADI AS 30	<<locked>>	68%	50633	90%	**94	100%
Accurate No. 11 FS	<<locked>>	65%	50865	90%	**50	100%
Accurate Solo 1000	<<locked>>	65%	49850	88%	**94	100%
Accurate Solo 1250	<<locked>>	62%	50082	89%	**20	100%
Baschieri & Pellagri 100	<<locked>>	62%	50125	89%	**91	100%
Hodgdon Clays	<<locked>>	72%	50676	90%	**78	100%
Hodgdon TrailBoss	<<locked>>	96%	33025	58%	**4	100%
Maxam CSB 1	<<locked>>	65%	49632	88%	**07	100%
Maxam CSB 3	<<locked>>	63%	49153	87%	**98	100%
Maxam CSB 4	<<locked>>	64%	50720	90%	**14	100%
Maxam CSB 5	<<locked>>	63%	49168	87%	**75	100%
ReloadSwiss RS 14	<<locked>>	96%	33228	59%	**04	100%
ReloadSwiss RS 30	<<locked>>	72%	50401	89%	**44	100%
SNPE Vectan A0	<<locked>>	63%	50589	89%	**47	100%
SNPE Vectan BA10	<<locked>>	67%	49240	87%	**75	100%
SNPE Vectan BA6 1/2	<<locked>>	77%	50691	90%	**88	100%
Somchem S265	<<locked>>	70%	49792	88%	**27	100%
Vihtavuori N110	<<locked>>	68%	49690	88%	**07	100%
Vihtavuori N32C Tin Star	<<locked>>	87%	50879	90%	**61	100%

Max Load - Barrel Length: 5.50''

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	61%	44976	80%	**66	100%
ADI APS 350	<<locked>>	61%	40103	71%	**63	100%
ADI APS 450	<<locked>>	61%	39987	71%	**73	100%
ADI AS 30	<<locked>>	61%	43149	76%	**19	100%
Accurate No. 11 FS	<<locked>>	61%	44469	79%	**78	99%
Accurate Solo 1000	<<locked>>	61%	46151	82%	**55	100%
Accurate Solo 1250	<<locked>>	61%	48153	85%	**98	100%
Baschieri & Pellagri 100	<<locked>>	61%	48153	85%	**71	100%
Hodgdon Clays	<<locked>>	61%	41394	73%	**79	100%
Hodgdon TrailBoss	<<locked>>	61%	18260	32%	**8	100%
Maxam CSB 1	<<locked>>	61%	45977	81%	**75	100%
Maxam CSB 3	<<locked>>	61%	47340	84%	**78	100%
Maxam CSB 4	<<locked>>	61%	47137	83%	**71	100%
Maxam CSB 5	<<locked>>	61%	47297	84%	**52	100%
ReloadSwiss RS 14	<<locked>>	61%	18478	33%	**4	100%
ReloadSwiss RS 30	<<locked>>	61%	35534	63%	**50	99%
SNPE Vectan A0	<<locked>>	61%	48747	86%	**27	100%
SNPE Vectan BA10	<<locked>>	61%	44034	78%	**15	100%
SNPE Vectan BA6 1/2	<<locked>>	61%	32561	58%	**75	100%
Somchem S265	<<locked>>	61%	38479	68%	**89	99%
Vihtavuori N110	<<locked>>	61%	39943	71%	**96	100%
Vihtavuori N32C Tin Star	<<locked>>	61%	31256	55%	**1	100%

Start Load - Barrel Length: 5.50''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data