
Load Specifications
Load data in caliber .22 Hornet with .224 | 45gr | Sierra SP HORNET bullet and 12 powders. The key underlying parameters are shown in the table above.
Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.
Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.
Charge: Powder weight in grains. Start with the minimum load and work up carefully.
FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.
MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.
V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.
z (Powder Burn): Estimated propellant combustion percentage at bullet exit.
A valid access license is required to use the Personalized Load Calculator.
You can find more information in our FAQ: How can I use the Personalized Load Calculator?
Max Load - Barrel Length: 24"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Hodgdon LilGun | <<locked>> | 92% | 38,232 psi | 88% | 2674 fps | 99.7% |
| Hodgdon LilGun | <<locked>> | 92% | 38,232 psi | 88% | 2674 fps | 99.7% |
| Hodgdon TrailBossᴾ | <<locked>> | 100% | 23,279 psi | 54% | 1614 fps | 100% |
| Hodgdon TrailBossᴾ | <<locked>> | 100% | 23,279 psi | 54% | 1614 fps | 100% |
| Lovex S040 | <<locked>> | 88% | 38,682 psi | 89% | 2503 fps | 98.7% |
| Lovex S040 | <<locked>> | 88% | 38,682 psi | 89% | 2503 fps | 98.7% |
| ReloadSwiss RS 14ᴾ | <<locked>> | 100% | 21,625 psi | 50% | 1631 fps | 100% |
| ReloadSwiss RS 14ᴾ | <<locked>> | 100% | 21,625 psi | 50% | 1631 fps | 100% |
| SNPE Vectan BA6 1/2ᴾ | <<locked>> | 100% | 29,138 psi | 67% | 2323 fps | 98.8% |
| SNPE Vectan BA6 1/2ᴾ | <<locked>> | 100% | 29,138 psi | 67% | 2323 fps | 98.8% |
| Vihtavuori N110ᴾ | <<locked>> | 100% | 36,738 psi | 84% | 2539 fps | 99.1% |
| Vihtavuori N110ᴾ | <<locked>> | 100% | 36,738 psi | 84% | 2539 fps | 99.1% |
Start Load - Barrel Length: 24"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Hodgdon LilGun | <<locked>> | 80% | 25,309 psi | 58% | 2382 fps | 96.7% |
| Hodgdon LilGun | <<locked>> | 80% | 25,309 psi | 58% | 2382 fps | 96.7% |
| Hodgdon TrailBoss | <<locked>> | 80% | 16,520 psi | 38% | 1434 fps | 100% |
| Hodgdon TrailBoss | <<locked>> | 80% | 16,520 psi | 38% | 1434 fps | 100% |
| Lovex S040 | <<locked>> | 80% | 30,458 psi | 70% | 2333 fps | 96.7% |
| Lovex S040 | <<locked>> | 80% | 30,458 psi | 70% | 2333 fps | 96.7% |
| ReloadSwiss RS 14 | <<locked>> | 80% | 16,143 psi | 37% | 1473 fps | 100% |
| ReloadSwiss RS 14 | <<locked>> | 80% | 16,143 psi | 37% | 1473 fps | 100% |
| SNPE Vectan BA6 1/2 | <<locked>> | 86% | 20,320 psi | 47% | 2067 fps | 95% |
| SNPE Vectan BA6 1/2 | <<locked>> | 86% | 20,320 psi | 47% | 2067 fps | 95% |
| Vihtavuori N110 | <<locked>> | 86% | 23,902 psi | 55% | 2241 fps | 95.2% |
| Vihtavuori N110 | <<locked>> | 86% | 23,902 psi | 55% | 2241 fps | 95.2% |
ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.
This overview compares 12 powders for .22 Hornet loaded with the .224 | 45gr | Sierra SP HORNET. Hodgdon LilGun delivers the highest muzzle velocity at 2,674 fps; across all powders the maximum-charge window runs from 1,614 fps to 2,674 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 12 of the 12 powders fall inside the usable 80–100 % fill window.
Relative to the caliber's maximum pressure (300 MPa), the top charges use 50–89 %, leaving at least 11 % headroom. Hodgdon TrailBoss, Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.