Load data for .219 Donaldson Wasp + .224 | 53gr | Hornady GMX

.219 Donaldson Wasp cartridge drawing
Hornady logo

Load Specifications

Bullet Manufacturer:Hornady
Bullet Weight:53 gr
Bullet Diameter:0.224"
Bullet Length:<<locked>>
Case Length (l3):1.81"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:35.1 Grains of Water
Primer Size:Large Rifle (LR)
Barrel Length:24"
Max. allowed Pressure:40,988 psi
Recommended Twist Rate:1:10.5

Load data in caliber .219 Donaldson Wasp with .224 | 53gr | Hornady GMX bullet and 8 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are IMR 3031, Accurate 2495 and Vihtavuori N135.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate 2015<<locked>>84%36,941 psi90%2959 fps97.6%
Accurate 2495<<locked>>90%35,723 psi87%2992 fps97.7%
Alliant AR-Comp<<locked>>86%35,694 psi87%3031 fps99.4%
Hodgdon TrailBossᴾ<<locked>>100%33,011 psi81%2083 fps100%
IMR 3031<<locked>>88%36,245 psi88%3048 fps96.6%
ReloadSwiss RS 14ᴾ<<locked>>100%33,156 psi81%2133 fps100%
Vihtavuori N133<<locked>>86%36,622 psi89%2923 fps97.4%
Vihtavuori N135<<locked>>90%35,259 psi86%2979 fps97.4%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate 2015<<locked>>80%32,764 psi80%2851 fps96.3%
Accurate 249523.5 gr84%29,573 psi72%2825 fps95.5%
Alliant AR-Comp<<locked>>80%29,660 psi72%2854 fps97.8%
Hodgdon TrailBoss<<locked>>80%24,642 psi60%1873 fps100%
IMR 303123.7 gr86%33,910 psi83%2982 fps95.7%
ReloadSwiss RS 14<<locked>>80%24,889 psi61%1923 fps100%
Vihtavuori N133<<locked>>80%30,792 psi75%2766 fps95.3%
Vihtavuori N13522.7 gr84%29,660 psi72%2818 fps95.2%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 8 powders for .219 Donaldson Wasp loaded with the .224 | 53gr | Hornady GMX. IMR 3031 delivers the highest muzzle velocity at 3,048 fps; across all powders the maximum-charge window runs from 2,083 fps to 3,048 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 8 of the 8 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (283 MPa), the top charges use 81–90 %, leaving at least 10 % headroom. The 53.0 gr projectile in 0.224" calls for a 1:10.5 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. IMR 3031, Accurate 2495, Vihtavuori N135 rank at the top here: for .219 Donaldson Wasp with the .224 | 53gr | Hornady GMX they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data