Load data for .218 Bee + .224 | 55gr | Rhino Solid Shank

.218 Bee cartridge drawing
Rhino Bullets logo

Load Specifications

Bullet Manufacturer:Rhino Bullets
Bullet Weight:55 gr
Bullet Diameter:0.224"
Bullet Length:<<locked>>
Case Length (l3):1.345"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:18 Grains of Water
Primer Size:Small Rifle (SR)
Barrel Length:24"
Max. allowed Pressure:46,412 psi
Recommended Twist Rate:1:12.5

Load data in caliber .218 Bee with .224 | 55gr | Rhino Solid Shank bullet and 9 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Vihtavuori N110, Lovex S053 and ADI AR 2205.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate No. 11 FS<<locked>>88%41,394 psi89%2526 fps97.1%
ADI AR 2205<<locked>>90%41,568 psi90%2451 fps98.7%
Hodgdon LilGun<<locked>>84%40,118 psi86%2592 fps100%
Hodgdon TrailBossᴾ<<locked>>100%25,904 psi56%1572 fps100%
Lovex S040<<locked>>82%39,958 psi86%2438 fps100%
Lovex S053ᴾ<<locked>>100%40,437 psi87%2536 fps98.6%
ReloadSwiss RS 14ᴾ<<locked>>100%25,164 psi54%1608 fps100%
SNPE Vectan BA6 1/2ᴾ<<locked>>100%37,449 psi81%2388 fps100%
Vihtavuori N110<<locked>>94%40,596 psi87%2503 fps100%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate No. 11 FS<<locked>>84%35,752 psi77%2421 fps95.6%
ADI AR 22059.9 gr80%30,400 psi66%2228 fps95.9%
Hodgdon LilGun<<locked>>80%34,403 psi74%2493 fps100%
Hodgdon TrailBoss<<locked>>80%18,652 psi40%1401 fps100%
Lovex S040<<locked>>80%37,956 psi82%2402 fps100%
Lovex S05310.3 gr88%28,761 psi62%2287 fps95.3%
ReloadSwiss RS 14<<locked>>80%18,275 psi39%1437 fps100%
SNPE Vectan BA6 1/2<<locked>>80%22,249 psi48%2054 fps99.1%
Vihtavuori N1108.9 gr80%26,629 psi57%2221 fps99.1%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 9 powders for .218 Bee loaded with the .224 | 55gr | Rhino Solid Shank. Hodgdon LilGun delivers the highest muzzle velocity at 2,592 fps; across all powders the maximum-charge window runs from 1,572 fps to 2,592 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 9 of the 9 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (320 MPa), the top charges use 54–90 %, leaving at least 10 % headroom. The 55.0 gr projectile in 0.224" calls for a 1:12.5 twist; slower twists will usually not stabilise this weight. Hodgdon TrailBoss, Lovex S053, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Vihtavuori N110, Lovex S053, ADI AR 2205 rank at the top here: for .218 Bee with the .224 | 55gr | Rhino Solid Shank they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data