Load data for .218 Bee + .224 | 50gr | Rhino Penetrator

.218 Bee cartridge drawing
Rhino Bullets logo

Load Specifications

Bullet Manufacturer:Rhino Bullets
Bullet Weight:50 gr
Bullet Diameter:0.224"
Bullet Length:<<locked>>
Case Length (l3):1.345"
Cartridge Length (C.O.L.):<<locked>>
Case Capacity:18 Grains of Water
Primer Size:Small Rifle (SR)
Barrel Length:24"
Max. allowed Pressure:46,412 psi

Load data in caliber .218 Bee with .224 | 50gr | Rhino Penetrator bullet and 9 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Vihtavuori N110, ADI AR 2205 and SNPE Vectan BA6 1/2.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.

Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.

Charge: Powder weight in grains. Start with the minimum load and work up carefully.

FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.

MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.

V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.

z (Powder Burn): Estimated propellant combustion percentage at bullet exit.

A valid access license is required to use the Personalized Load Calculator.

You can find more information in our FAQ: How can I use the Personalized Load Calculator?

Max Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate No. 11 FS<<locked>>90%41,858 psi90%2661 fps96.3%
ADI AR 2205<<locked>>92%41,611 psi90%2575 fps98%
Hodgdon LilGun<<locked>>86%40,495 psi87%2743 fps100%
Hodgdon TrailBossᴾ<<locked>>100%25,106 psi54%1654 fps100%
Lovex S040<<locked>>84%40,437 psi87%2579 fps99.9%
Lovex S053ᴾ<<locked>>100%38,058 psi82%2618 fps97.4%
ReloadSwiss RS 14ᴾ<<locked>>100%24,337 psi52%1693 fps100%
SNPE Vectan BA6 1/2ᴾ<<locked>>100%35,534 psi77%2487 fps100%
Vihtavuori N110<<locked>>96%40,495 psi87%2641 fps100%

Recommended = one of the top powders for this cartridge and bullet combination.

Start Load - Barrel Length: 24"

PowderChargeFRMaxP%V(0)z
Accurate No. 11 FS<<locked>>88%39,001 psi84%2608 fps95.5%
ADI AR 220510.5 gr82%31,459 psi68%2365 fps95.2%
Hodgdon LilGun<<locked>>80%33,112 psi71%2605 fps99.9%
Hodgdon TrailBoss<<locked>>80%18,202 psi39%1476 fps100%
Lovex S040<<locked>>80%36,666 psi79%2507 fps99.7%
Lovex S053<<locked>>92%30,763 psi66%2457 fps95.1%
ReloadSwiss RS 14<<locked>>80%17,796 psi38%1516 fps100%
SNPE Vectan BA6 1/28.8 gr80%20,943 psi45%2119 fps97.9%
Vihtavuori N1109.2 gr80%25,527 psi55%2313 fps98.2%

Recommended = one of the top powders for this cartridge and bullet combination.

ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.

<<locked>> you need an access license to unlock this data.

This overview compares 9 powders for .218 Bee loaded with the .224 | 50gr | Rhino Penetrator. Hodgdon LilGun delivers the highest muzzle velocity at 2,743 fps; across all powders the maximum-charge window runs from 1,654 fps to 2,743 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 9 of the 9 powders fall inside the usable 80–100 % fill window.

Relative to the caliber's maximum pressure (320 MPa), the top charges use 52–90 %, leaving at least 10 % headroom. Hodgdon TrailBoss, Lovex S053, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Vihtavuori N110, ADI AR 2205, SNPE Vectan BA6 1/2 rank at the top here: for .218 Bee with the .224 | 50gr | Rhino Penetrator they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.

← All load data