Load Specifications
Load data in caliber .218 Bee with .224 | 50gr | Remington PSP bullet and 9 powders. The key underlying parameters are shown in the table above. The recommended powders for this cartridge and bullet combination are Vihtavuori N110, ADI AR 2205 and SNPE Vectan BA6 1/2.
Important Notice: DO NOT go below Minimum Charge or above Maximum Charge. Since we have no control over the equipment and components used, any responsibility and liability for the results achieved is rejected.
Only powders/loads that match the current filter criteria are displayed: max pressure of a load ≤ 90% of max. standardized pressure, fill rate ≥ 80% and propellant combustion ≥ 95%. Use the sliders above the tables to adjust these thresholds.
Charge: Powder weight in grains. Start with the minimum load and work up carefully.
FR (Fill Rate): Case fill as a percentage. Values above 100% mean compressed loads.
MaxP / %: Maximum chamber pressure in bar and as a percentage of the standardized maximum for this caliber.
V(0): Muzzle velocity in feet per second (fps) at the standardized barrel length.
z (Powder Burn): Estimated propellant combustion percentage at bullet exit.
A valid access license is required to use the Personalized Load Calculator.
You can find more information in our FAQ: How can I use the Personalized Load Calculator?
Max Load - Barrel Length: 24"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Accurate No. 11 FS | <<locked>> | 90% | 41,872 psi | 90% | 2667 fps | 96.4% |
| ADI AR 2205 | <<locked>> | 90% | 39,697 psi | 86% | 2549 fps | 97.7% |
| Hodgdon LilGun | <<locked>> | 86% | 40,567 psi | 87% | 2749 fps | 100% |
| Hodgdon TrailBossᴾ | <<locked>> | 100% | 25,570 psi | 55% | 1667 fps | 100% |
| Lovex S040 | <<locked>> | 84% | 41,640 psi | 90% | 2608 fps | 100% |
| Lovex S053ᴾ | <<locked>> | 100% | 39,073 psi | 84% | 2644 fps | 97.7% |
| ReloadSwiss RS 14ᴾ | <<locked>> | 100% | 24,801 psi | 53% | 1706 fps | 100% |
| SNPE Vectan BA6 1/2ᴾ | <<locked>> | 100% | 35,650 psi | 77% | 2497 fps | 100% |
| Vihtavuori N110 | <<locked>> | 96% | 41,611 psi | 90% | 2667 fps | 100% |
Recommended = one of the top powders for this cartridge and bullet combination.
Start Load - Barrel Length: 24"
| Powder | Charge | FR | MaxP | % | V(0) | z |
|---|---|---|---|---|---|---|
| Accurate No. 11 FS | <<locked>> | 86% | 37,260 psi | 80% | 2582 fps | 95.2% |
| ADI AR 2205 | 10.6 gr | 82% | 31,560 psi | 68% | 2375 fps | 95.4% |
| Hodgdon LilGun | <<locked>> | 80% | 33,286 psi | 72% | 2612 fps | 100% |
| Hodgdon TrailBoss | <<locked>> | 80% | 18,666 psi | 40% | 1496 fps | 100% |
| Lovex S040 | <<locked>> | 80% | 36,840 psi | 79% | 2516 fps | 99.7% |
| Lovex S053 | <<locked>> | 92% | 30,893 psi | 67% | 2467 fps | 95.3% |
| ReloadSwiss RS 14 | <<locked>> | 80% | 17,579 psi | 38% | 1512 fps | 100% |
| SNPE Vectan BA6 1/2 | 8.9 gr | 80% | 21,161 psi | 46% | 2133 fps | 98.1% |
| Vihtavuori N110 | 9.3 gr | 80% | 25,773 psi | 56% | 2326 fps | 98.3% |
Recommended = one of the top powders for this cartridge and bullet combination.
ᴾ possible press load - work up slowly to this load while watching for signs of excessive pressure.
This overview compares 9 powders for .218 Bee loaded with the .224 | 50gr | Remington PSP. Hodgdon LilGun delivers the highest muzzle velocity at 2,749 fps; across all powders the maximum-charge window runs from 1,667 fps to 2,749 fps. Hodgdon TrailBoss gives the best case fill at 100 %, and 9 of the 9 powders fall inside the usable 80–100 % fill window.
Relative to the caliber's maximum pressure (320 MPa), the top charges use 53–90 %, leaving at least 10 % headroom. Hodgdon TrailBoss, Lovex S053, ReloadSwiss RS 14 reach 100 % fill or more at maximum charge, so these are compressed loads: they need a long drop tube to seat cleanly and react sensitively to the case capacity of your own brass lot. Vihtavuori N110, ADI AR 2205, SNPE Vectan BA6 1/2 rank at the top here: for .218 Bee with the .224 | 50gr | Remington PSP they combine a high case fill with complete burn and sit in the upper velocity band. Always begin at the start load and work up in small increments while checking case and primer for pressure signs.